MSE-XT220 Laser Distance Measurement Sensor
Laser Distance Measurement Sensors MSE-XT220 Description Technical Info Housing Info Data Sheet Request More Info
 
Back view of the MSE-XT220 Laser Distnace Measurement Sensor with the Power Section cover removed showing the 12 pointer terminal block.

The Back view of the MSE-XT220 Laser Distance Measurement Sensor with the Power Section Cover removed showing the 12 point terminal block.

Housing Technical Information

The MSE-XT220 Laser Distance Measurement Sensor a cast copper free aluminum explosion proof housing. The housing consists of 3 components. A center main body section with (2) 3/4"-14 NPT conduit entry points, an instrumentation section with a glass window cover, and a power section with a solid cover. The instrumentation section cover and the power section cover screws onto the main body and is secured with a set screw.

The center main body section is attached to aluminum mounting plate. Wiring to the laser is run to this section through the conduit entry points. 

The laser sensor electronic circuitry is packaged inside of the instrumentation section. The instrumentation section cover should never be removed except by authorized and certified factory service technicians

The housing meets Explosion Proof Certifications for Class I, Groups B, C, D; Class II, E, F, G; Class III, NEMA 7BCD and NEMA 9EFG. The housing can also be used in IP66 and NEMA 4X water tight applications. The housing has a corrosion resistant, "Safety Blue" polyester powder coating and utilizes stainless steel hardware.

Standard operating temperature range is -10°C (-4°F) to 50°C (122°F). An optional Factory Installed 24 VDC PTC Heater is available to allow operation down to -40°C (-40°F)

WARNING: TO PREVENT IGNITION OF HAZARDOUS DO NOT REMOVE THE POWER COVER WHILE CIRCUITS ARE ALIVE. KEEP ASSEMBLY TIGHTLY CLOSED WHILE IN OPERATION. FOR CLASS I GROUPS B,C,D CONDUIT SEALS ARE REQUIRED WITHIN 457mm (18in) .
 
 

Housing Specifications
Housing Material
Sand Cast Copper Free Aluminum, Corrosion Resistant Polyester Powder Coating, Stainless Steel Hardware, Tempered Glass Window
Housing Rating
Watertight: IP66, NEMA 4X
Explosion Proof: Class I, Groups B, C, D; Class II, E, F, G; Class III, NEMA 7BCD and NEMA 9EFG
Mounting Plate Material
6061 T6 Aluminum; Finish: Blue Anodize
Weight
5.8 Kg (12.8LB)
Electrical Connection
Internal 12 Point Terminal Block
Operating Temperature
-20°C (-4°F) to +50°C (122°F)
-40°C (-40°F) to +50°C (122°F) with optional internal 24 VDC PTC Heater
Storage Temperature
-20°C (-4°F) to +50°C (122°F)
 
Housing Dimensions
MSE-XT220 Laser Distance Measurement Sensor Housing Dimensional Imformation
 

Part Number Specifications
Model Number
Description
MSE-XT220-1
MSE-XT220 with RS232 Serial Interface
MSE-XT220-2
MSE-XT220 with RS422/RS485 Serial Interface
MSE-XT220-1-H
MSE-XT220 with RS232 Serial Interface with optional 24VDC PTC Heater
MSE-XT220-2-H
MSE-XT220 with RS422/RS485 Serial Interface with optional 24VDC PTC Heater
Please contact us for additional information on Model Numbers for other FieldBus Interface Options. 
 

Electrical Connection Information

Electical Connections
Pin No.
Wire Color
Designation
Function  if RS232
Function if RS422/RS485
1
Green
TxD / RX+
RS232 send data
RS422 receive data +
2
Yellow
RxD / RX-
RS232 receive data
RS422 receive data
3
Brown
TRIG
External Trigger
External Trigger
4
Red
IOUT
Analog Current Output
Analog Current Output
5
Black
TX-
Not Used
RS422 send data +
6
Violet
TX+
Not Used
RS422 send data
7
Pink
VCC
Supply Voltage
Supply Voltage
8
White
ALARM
Digital switching output
Digital switching output
9
Gray
GND
Ground Potential (Signal)
Ground Potential (Signal)
10
Blue
GND
Ground Potential (Supply)
Ground Potential (Supply)
11
Black
+24VDC
PTC Heater Supply (Optional)
PTC Heater Supply (Optional)
12
Black
0VDC
PTC Heater Supply (Optional)
PTC Heater Supply (Optional)
 
 

The MSE-XT220 Laser Distance Measurement sensor is a direct replacement for the Moduloc Model LT2000-XT and the LT2020-XT. Please contact us for additional information or if you have a similar Model Number that you need pricing on or a replacement for.
 
Laser Distance Measurement Sensors MSE-XT220 Description Technical Info Housing Info Data Sheet Request More Info
HOME Laser Distance Measurement Sensors Laser Level Sensors Optical Position Looper Scanner